Ghost Controls Gate Parts & Welding in Cleveland, OH

Ghost Controls Gate Parts & Welding in Cleveland: What to Know First

We provide independent Ghost Controls gate parts and welding service throughout Cleveland, typically completing hinge replacements, post repairs, and rail welding in a single visit with upfront pricing agreed before we start. Most Ghost Controls jobs run $280-$750 depending on whether we’re replacing a single hinge or welding a sagging rail back to true. We’re not affiliated with Ghost Controls - we’re an independent service provider - which means we source the right part for your specific model, not whatever ships fastest from a warehouse.

Call (855) 949-2853

This page is for Cleveland homeowners running a Ghost Controls TSS1, TDS2, or AX series opener who’ve noticed grinding, sagging, or binding that the motor itself can’t fix. The gate hardware fails before the electronics do, and that’s where we come in. Call (855) 949-2853 - a live person answers, 24 hours a day, 7 days a week.

How Ghost Controls Products Fail - and How We Fix Them

• TSS1 series hinge fatigue on heavier ornamental gates. The TSS1 is built for light-to-midweight swing gates, but in Cleveland we see them paired with wrought-iron frames that weigh more than the spec allows. The bottom hinge pin ovalizes first. We replace with a beefier J-bolt hinge, sometimes welding a reinforcement plate to the post if the wood has compressed.
• TDS2 dual-swing rail separation at the center stop. The TDS2’s center stop bracket takes a beating from wind gusts coming off Lake Erie, especially in neighborhoods like Bratenahl and Clifton where gates catch the full fetch. The rail welds crack at the stop. We cut out the fatigue, weld in a thicker wall tube, and reset the stop so the motors aren’t fighting misalignment.
• AX series roller seizure on slide gates. The AX1 and AX2 use V-groove steel rollers that rust solid after three or four Cleveland winters if the owner doesn’t grease them religiously. The motor keeps trying, overheats, and throws a fault code. We replace the rollers with sealed stainless units and weld new mounting tabs if the originals have wallowed out.
• Latch misalignment after post heave. Cleveland’s clay-heavy soils in West Park and Parma Heights shift with freeze-thaw, tilting the receiving post while the gate post stays put. The Ghost Controls magnetic latch won’t make contact, so owners start using the manual release daily. We plumb the post, weld a new strike plate in the corrected position, and test the auto-close timer.
• Gate frame weld failure at the picket-to-rail joint. Ornamental aluminum gates with Ghost Controls openers often fail where the vertical pickets meet the top rail - not from weight, but from vibration fatigue as the opener starts and stops. We grind back to sound metal, TIG weld the joint, and add a gusset where the stress concentrates.

Our Ghost Controls Gate Parts & Welding Process

1. 1
   Call and describe what you’re seeing. A live person answers - no voicemail, no callback queue. We’ll ask if it’s a swing or slide gate, which Ghost Controls model, and whether the motor runs but the gate won’t move, or if something looks bent or broken.
2. 2
   On-site diagnosis. Our tech arrives in a marked van with the K.E.Y.S. patch on the uniform. We cycle the gate manually, check post plumb, and identify whether the problem is the opener, the hardware, or both. We explain it in plain language before touching a wrench.
3. 3
   Parts decision with you. For Ghost Controls, we stock common hinges, rollers, and latch kits. If your part is proprietary, we’ll quote OEM versus a quality aftermarket equivalent that won’t void your opener warranty. You choose. We don’t substitute without asking.
4. 4
   The repair and weld. We weld with 220-volt MIG or TIG depending on the metal - steel, aluminum, or wrought iron. Every weld gets a visual inspection and a stress test before we call it done. If it’s worth putting on your property, it’s worth fixing right the first time.
5. 5
   Full-cycle testing and cleanup. We run the opener through its full open-close-open sequence at least five times, check the safety reverse, and torque every bolt. Then we sweep the work area. You get a written invoice and the 90-Day Done Right Promise before we leave.

What Ghost Controls Gate Parts & Welding Costs in Cleveland

These are Cleveland market ranges for 2024-2025. We settle on an exact price before starting, and we honor our standing offers: $50 off any repair over $250, free second opinion on any written estimate, and a permanent 5% senior and veteran discount. Call (855) 949-2853 for a free estimate - we’ll come look at it, no charge.

Why Cleveland Homeowners Call Ironworks Gate Co. of Cleveland for Ghost Controls Work

We’ve been fixing gates in Cleveland since 2013. Dale Morrow started this company after welding training at Cuyahoga Community College and years of hands-on work across every kind of gate system in Greater Cleveland. That means when your Ghost Controls TDS2 is binding, we know whether the problem started with the opener, the hardware, or the frost-heaved post - and we don’t replace parts that aren’t broken.

Our technicians carry Ghost Controls parts alongside LiftMaster, Mighty Mule, DoorKing, and five other brands. If your Ghost Controls opener has reached end of life, we can quote a replacement that fits your existing gate without a hard sell. The 90-Day Done Right Promise covers every job, written and plain: if it’s not right, we come back and make it right. No paperwork to file, no argument. Most repairs finish in one visit because our vans are stocked for it. And when you call, a live person answers - 24 hours a day, 7 days a week - because a gate that won’t close on a Saturday night in Cleveland Heights is still a problem at 9 PM.

FAQs